Free in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Before
After
Before
After
Before
AfterWindows & Doors in Coconut Creek, FL
Window and door installation in Coconut Creek runs $650-$4,200 per opening depending on product tier, with most full-home projects falling between $8,500 and $22,000. Every job we take in this city starts with a measured survey under Haven Clause 1, because Coconut Creek’s housing stock - dominated by 1970s-era condos with original single-pane aluminum frames and newer subdivisions with pre-2002 builder-grade units - presents conditions we document before quoting, not after. Call (754) 254-7558 to schedule your free measured survey and written estimate.
Why Coconut Creek Homes Are Different
Coconut Creek sits entirely within Broward County’s High Velocity Hurricane Zone, one of only two US counties where every replacement window and door must carry Miami-Dade County Product Approval - a stricter standard than neighboring Palm Beach County. The city’s housing is anchored by massive planned communities like Wynmoor Village, where thousands of 55+ condo units still hold original single-pane aluminum windows and unrated sliding glass doors that fail both HVHZ code and current Florida insurer requirements.
This creates a replacement market driven by insurance mandates rather than preference alone. In Wynmoor and comparable 1970s complexes, contractors must clear dual approval: a Broward County building permit plus HOA architectural review. That lag is built into our scheduling, not discovered mid-project. Year-round heat, humidity, and UV radiation also accelerate frame oxidation and seal failure in the city’s prevalent older aluminum units, shortening replacement cycles compared to drier inland markets.
Our Main Coconut Creek Services
Most calls we field from Coconut Creek homeowners center on two needs: replacing failing original windows in aging condo communities and upgrading to HVHZ-compliant impact-rated products that satisfy insurer and code requirements.
Window Replacement in Coconut Creek
We replace original single-pane aluminum and pre-2002 builder-grade vinyl windows across Coconut Creek’s condo and single-family stock, from Wynmoor Village’s 1970s units to 1990s subdivisions near the Promenade. Every replacement carries Miami-Dade NOA certification and leaves a documented photo record under Haven Clause 4. Window Replacement in Coconut Creek covers our full process, product lines, and pricing structure.
Impact Windows & Doors in Coconut Creek
HVHZ compliance is not optional in Coconut Creek - it’s code. We install impact-rated windows and doors from PGT, CGI, and ES Windows that carry the NOA required for Broward County permits, with written proof of compliance provided before work begins. Impact Windows & Doors in Coconut Creek details our impact product tiers and permit-handling process.
Sliding & Patio Doors in Coconut Creek
Original sliding glass doors in Coconut Creek’s older communities are frequently the weakest point in the envelope - unrated, single-pane, and prone to derailment. We replace them with impact-rated, multi-panel systems that meet HVHZ standards and pass HOA architectural review. Sliding & Patio Doors in Coconut Creek explains our measured survey and installation protocol for these large openings.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Before
AfterWindow Installation in Coconut Creek
Window installation in Coconut Creek means working within HVHZ code requirements that apply to every opening, not just coastal properties. The city’s 1970s condo stock - Wynmoor Village, Countrywood, and similar planned communities - holds thousands of original single-pane aluminum windows that now fail both insurer requirements and the 2002 Florida Building Code. Our Window Installation process begins with a measured survey that becomes your written quote, with no deviation between the two documents.
Single & Double Hung Windows
Signs you need it
Frames show oxidation pitting, sashes stick or drop, or you feel air movement at the meeting rail during a blower door test.
What it costs in Coconut Creek
Single and double hung window installation in Coconut Creek typically runs $650-$1,400 per opening for vinyl and $1,200-$2,800 for aluminum-clad or impact-rated units.
How we do it
We measure rough opening to 1/8 inch, verify NOA compliance for the specific product, install with HVHZ-approved anchoring, and document with photos before, during, and after.
Horizontal Roller Windows
Signs you need it
Rollers grind or jump track, weatherstripping is brittle, or the sash no longer seals against the jamb under light pressure.
What it costs in Coconut Creek
Horizontal roller window installation in Coconut Creek ranges $750-$1,550 for standard vinyl and $1,400-$3,100 for impact-rated aluminum systems.
How we do it
We verify sill slope and drainage path, set the frame with stainless steel fasteners at specified spacing, adjust roller tension, and seal with approved membrane and backer rod.
What Window Installation Costs in Coconut Creek
| Item | Typical range in Coconut Creek |
|---|---|
| Single/Double Hung Vinyl Window | $650 - $1,400 |
| Single/Double Hung Impact Window | $1,200 - $2,800 |
| Horizontal Roller Vinyl Window | $750 - $1,550 |
| Horizontal Roller Impact Window | $1,400 - $3,100 |
| Full-home project (10-15 openings) | $8,500 - $22,000 |
Do you pull permits for window replacement in Coconut Creek?
Yes - Broward County requires a building permit for every window replacement in the HVHZ, and we pull and close all permits as part of our scope. The permit cost and inspection scheduling are included in your written quote; you will not receive a separate invoice from the county. Call (754) 254-7558 to schedule your free measured survey.
Will my HOA need to approve the window style?
Nearly every Coconut Creek condo community, including Wynmoor Village, requires HOA architectural review before work begins; we provide product cut sheets, NOA documentation, and color samples for your submittal. Our crews do not start demolition until written HOA approval and the county permit are both in hand. Call (754) 254-7558 and we will walk you through the dual-approval timeline.
Door Installation in Coconut Creek
Door installation in Coconut Creek faces the same HVHZ mandate as windows: every exterior door must carry Miami-Dade NOA, and the city’s 1970s-era stock holds thousands of hollow-core or unrated steel doors that fail current code. We install entry, patio, and storm door systems from Therma-Tru and other verified lines, with Door Installation pricing fixed to the measured survey before work begins.
Entry Doors
Signs you need it
Door slab is delaminating, frame is soft at the sill, or daylight is visible around the perimeter when closed.
What it costs in Coconut Creek
Entry door installation in Coconut Creek runs $1,800-$4,200 for fiberglass or steel units, and $3,500-$6,800 for impact-rated systems with HVHZ-compliant hardware.
How we do it
We measure rough opening and jamb depth, verify NOA and fire-rating if required, install with three-point locking and approved anchors, and seal with integrated sill pan and flashing tape.
Hurricane-Proof Front & Entry Doors
Signs you need it
Your insurer has flagged the existing door as non-compliant, or the current unit lacks a Miami-Dade NOA label visible on the hinge edge.
What it costs in Coconut Creek
Impact-rated front door systems in Coconut Creek range $3,500-$6,800 installed, including HVHZ hardware, multi-point lock, and permit.
How we do it
We specify the door and frame as a tested assembly, submit NOA with the permit application, install with impact-rated hinges and deadbolt strike, and pass county inspection before final payment.
What Door Installation Costs in Coconut Creek
| Item | Typical range in Coconut Creek |
|---|---|
| Standard Fiberglass/Steel Entry Door | $1,800 - $4,200 |
| Impact-Rated Front Door System | $3,500 - $6,800 |
| French Door Pair (impact-rated) | $4,200 - $8,500 |
Do French doors count as one opening or two for permitting?
Broward County counts a French door pair as two separate openings for HVHZ permitting, which affects both permit fees and inspection scheduling; we account for this in your written quote so there is no surprise. Call (754) 254-7558 for a measured survey and itemized estimate.
Can you match my HOA’s color requirements?
We carry color samples from all eight manufacturer lines and submit the selected finish with your HOA architectural package before ordering; production lead times vary by manufacturer, and we build that into the project schedule. Call (754) 254-7558 to review available finishes.
Energy-Efficient Windows in Coconut Creek
Energy-efficient windows in Coconut Creek address a specific climate burden: year-round cooling loads, intense UV degradation, and humidity-driven condensation in older aluminum frames. The city’s inland position does not reduce solar gain meaningfully - it increases it, with fewer afternoon cloud breaks than coastal Broward. Our Energy-Efficient Windows are specified by U-factor and SHGC to match Coconut Creek’s cooling-dominated load profile, not a generic national standard.
Low-E & Argon Gas Glass
Signs you need it
Your current windows are single-pane or pre-2002 double-pane without Low-E coating, and your summer cooling bills exceed $280 monthly for a 1,200-square-foot condo.
What it costs in Coconut Creek
Low-E with argon fill, installed in Coconut Creek, typically adds $80-$140 per opening over standard dual-pane, with full payback in 4-7 years at current FPL rates.
How we do it
We specify the coating surface by climate zone, verify argon concentration at delivery, and document NFRC label values on your photo record for tax credit eligibility.
ENERGY STAR Replacement Windows
Signs you need it
You are replacing windows for insurance compliance and want to capture available federal tax credits, or your utility rebate program requires ENERGY STAR certification.
What it costs in Coconut Creek
ENERGY STAR certified window installation in Coconut Creek runs $850-$1,750 per opening for vinyl and $1,500-$3,200 for impact-rated systems that also carry the certification.
How we do it
We cross-reference the NFRC certified products directory with our manufacturer lines, confirm the specific product qualifies for current tax credits, and provide the NFRC label documentation with your closing packet.
What Energy-Efficient Windows Costs in Coconut Creek
| Item | Typical range in Coconut Creek |
|---|---|
| Low-E/Argon Upgrade (add to base window) | $80 - $140 per opening |
| ENERGY STAR Vinyl Window | $850 - $1,750 |
| ENERGY STAR Impact-Rated Window | $1,500 - $3,200 |
Will energy-efficient windows lower my FPL bill in Coconut Creek?
Yes - in Coconut Creek’s cooling-dominated climate, Low-E/argon windows with SHGC below 0.25 typically reduce cooling load 12-18% compared to single-pane aluminum, with savings concentrated in May through October. Call (754) 254-7558 and we will model the payback using your current window type and square footage.
Do energy-efficient windows still need to be impact-rated?
All replacement windows in Coconut Creek must be impact-rated or protected with approved shutters regardless of energy performance; we specify products that meet both requirements, and the ENERGY STAR and NOA documentation travel together in your packet. Call (754) 254-7558 to review qualifying products.
Impact Garage Doors in Coconut Creek
Impact garage doors in Coconut Creek are frequently the last opening homeowners address, but they are often the largest unprotected surface in the envelope. The city’s 1990s and early-2000s single-family subdivisions - Winston Park, Lyons Gate, and similar - were built with non-rated sectional doors that fail HVHZ and current insurer requirements. Our Impact Garage Doors carry the Miami-Dade NOA required for permit approval and are specified by wind-load rating for your specific exposure category.
Hurricane-Rated Garage Doors
Signs you need it
Your garage door lacks a visible Miami-Dade NOA label, or your insurer has specifically listed the garage door as non-compliant in your wind mitigation inspection.
What it costs in Coconut Creek
Hurricane-rated garage door replacement in Coconut Creek ranges $2,800-$5,500 for a standard 16-by-7-foot sectional, and $4,200-$7,800 for oversized or custom-height residential openings.
How we do it
We measure the opening and verify exposure category, specify the door and track as a tested assembly with rated hardware, pull the permit, and install with reinforced struts and approved jamb anchors.
Wind-Load Code Compliance
Signs you need it
You are selling or refinancing and the buyer’s inspection flagged the garage door, or your four-point inspection notes a non-rated door in a home built before 2002.
What it costs in Coconut Creek
Wind-load retrofit or replacement for code compliance in Coconut Creek runs $2,800-$5,500 for standard sizes, with permit and inspection included in the written quote.
How we do it
We verify the design pressure required for your Coconut Creek address, match the door to that rating with documentation, install with proper track reinforcement, and schedule county inspection before final walkthrough.
What Impact Garage Doors Costs in Coconut Creek
| Item | Typical range in Coconut Creek |
|---|---|
| Standard Hurricane-Rated Sectional (16′ x 7′) | $2,800 - $5,500 |
| Oversized/Custom Height Residential | $4,200 - $7,800 |
| Wind-Load Retrofit (hardware/track upgrade) | $1,800 - $3,400 |
Does my garage door need impact-rated glass too?
If your garage door has glazing - windows, inserts, or full-view sections - that glass must also be impact-rated and labeled; we specify doors with integrated impact glazing or solid panels, and the NOA covers the complete assembly. Call (754) 254-7558 to inspect your current door and quote the compliant replacement.
Will a new impact garage door lower my insurance premium?
A Miami-Dade NOA-rated garage door improves your wind mitigation inspection score, which insurers use to set discounts; the exact reduction varies by carrier, and we provide the NOA documentation for your agent. Call (754) 254-7558 to schedule inspection and written quote.
Custom & Geometric Windows in Coconut Creek
Custom and geometric windows in Coconut Creek solve a specific problem: the 1970s and 1980s condo stock, particularly in Wynmoor Village and similar communities, was built with shaped openings - arches, rounds, and extended rectangles - that standard replacement sizes do not fit. These units were originally single-pane and are now failing, but the geometry complicates both product selection and HVHZ compliance. Our Custom & Geometric Windows are measured to the finished opening and fabricated to NOA-approved configurations.
Geometric & Shaped Windows
Signs you need it
Your window is not rectangular - it is arched, circular, triangular, or a combination shape - and the frame shows leakage, fogging, or structural fatigue at the mullion joints.
What it costs in Coconut Creek
Geometric and shaped window installation in Coconut Creek ranges $1,800-$4,200 per opening for standard configurations, and $3,500-$7,500 for complex multi-section or impact-rated custom fabrications.
How we do it
We template the exact radius and angle with digital measurement, submit the drawing to the manufacturer for NOA verification, fabricate in the specified glazing, and install with custom flashings matched to the wall assembly.
Arched & Curved Windows
Signs you need it
The arched top sash in your living room or entryway is single-pane, the curved frame has separated at the springline, or condensation runs down the radius and stains the interior sill.
What it costs in Coconut Creek
Arched window replacement in Coconut Creek runs $2,200-$4,800 for vinyl and $3,800-$7,200 for impact-rated aluminum, with radius templates included in the measured survey.
How we do it
We establish the true radius and springline height, verify the manufacturer’s NOA includes that specific arch configuration, fabricate with insulated laminated glass, and install with pre-formed head flashing to match the curve.
What Custom & Geometric Windows Costs in Coconut Creek
| Item | Typical range in Coconut Creek |
|---|---|
| Geometric/Shaped Window (standard config) | $1,800 - $4,200 |
| Geometric/Shaped Window (impact-rated custom) | $3,500 - $7,500 |
| Arched Window (impact-rated aluminum) | $3,800 - $7,200 |
Can you replicate my original arched window exactly?
We template the existing opening to 1/16 inch and fabricate to match the sightline and proportion, but the glazing will be insulated laminated or impact-rated per HVHZ code; the look is replicated, the performance is modern. Call (754) 254-7558 to schedule template measurement.
Do custom shapes take longer to permit in Broward County?
Custom configurations require the county plan reviewer to verify the specific NOA drawing matches your template, which can add 5-10 business days to permit issuance; we submit complete documentation upfront to avoid revision cycles. Call (754) 254-7558 and we will confirm current Broward County review timelines.
Brands We Service in Coconut Creek
We install and service eight verified manufacturer lines in Coconut Creek: PGT, CGI, CWS, ES Windows, ECO Window Systems, Mr-Glass, Therma-Tru, and ViewLux. Parts for ES Windows, ECO Window Systems, and Therma-Tru are stocked at our Miami office for same-week turnaround on most service calls. See our brands for performance tiers and specifications by product category.
Pricing for Windows & Doors in Coconut Creek, FL
| Service | Typical range in Coconut Creek |
|---|---|
| Single/Double Hung Vinyl Window | $650 - $1,400 |
| Single/Double Hung Impact Window | $1,200 - $2,800 |
| Horizontal Roller Vinyl Window | $750 - $1,550 |
| Horizontal Roller Impact Window | $1,400 - $3,100 |
| Standard Fiberglass/Steel Entry Door | $1,800 - $4,200 |
| Impact-Rated Front Door System | $3,500 - $6,800 |
| Low-E/Argon Upgrade (per opening) | $80 - $140 |
| ENERGY STAR Impact-Rated Window | $1,500 - $3,200 |
| Hurricane-Rated Garage Door (16′ x 7′) | $2,800 - $5,500 |
| Geometric/Shaped Window (impact custom) | $3,500 - $7,500 |
| Arched Window (impact-rated aluminum) | $3,800 - $7,200 |
| Full-home window project (10-15 openings) | $8,500 - $22,000 |
Prices in Coconut Creek push toward the higher end when HOA architectural review requires custom colors, when existing aluminum frames need full-frame removal rather than insert replacement, or when Broward County requires engineering for non-standard openings. Your written quote, delivered before any work starts under Haven Clause 1, is the price on the final invoice - no change orders, no surprises.
Neighborhoods We Serve in Coconut Creek
We work across Coconut Creek’s full housing spectrum, from the 1970s condo villages to newer single-family subdivisions. Scheduling and dispatch are coordinated from our Miami office; most Coconut Creek appointments are available within 3-5 business days of your call.
- Wynmoor Village
- Winston Park
- Lyons Gate
- Countrywood
- Turtle Run
Service Area - Cities Near Coconut Creek
Our crews serve the full Broward County HVHZ corridor from the Miami office. We regularly install and replace windows and doors in Margate, FL, Pompano Beach, FL, Coral Springs, FL, and Deerfield Beach, FL, with the same measured-survey protocol and written-price guarantee applied to every appointment.
Serving Coconut Creek, FL - Our Local Coverage Area
We’re based in the Coconut Creek area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Windows & Doors in Coconut Creek
Most Coconut Creek HOAs, including Wynmoor Village, require 2-4 weeks for architectural review after submittal; Broward County adds another 10-15 business days for HVHZ permit review. We build this lag into your project schedule and do not order product until both approvals are in hand.
Yes - we have completed hundreds of openings in Wynmoor Village and similar 55+ communities, and we understand the board submittal process, insurance certificate requirements, and work-hour restrictions that apply to these properties.
It does not - we verify NOA compliance, install to manufacturer specifications, and schedule inspection only when the work is documented and complete; if a Broward County inspector identifies a deficiency, we correct it at our cost under the 365-Day Done Right Promise. Call (754) 254-7558 to discuss our inspection-pass record.
Call (754) 254-7558 to schedule your free measured survey and written estimate. Every Coconut Creek project starts with a documented survey you keep, a fixed price before any work begins, and a photo record when the job is done - governed by the Haven Standard since 2012.
What happens when you call
- 1A real person answersNo phone trees - talk to a local windows & doors pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Coconut Creek Customers Say
"The road noise in the front bedroom is genuinely gone. They recommended the laminated glass and explained why, with figures."
- Delia F."Replaced eight windows. They showed me the U-factor on the units they were actually fitting rather than the brochure numbers."
- Kofi B."Patio door had dropped and would not lock. They adjusted it rather than selling me a new one, and charged accordingly."
- Simone T.